Element 9.30
Glass making
- Sheet
- 9.30
- Chapter
- 9 Manufacturing and repair
- State
- Drafted
- Release
- 16 November 2026
- Editor
- Contributed by Praecise as open research
- Reviewers
- To be named at review
- Safety
- S3, as the chapter
- Licence
- CC BY-SA 4.0
- Resources
- 6
The element
- Requirement
Glass is melted only in a furnace that is sited, run and maintained to prevent fire and burns, by people protected from silica dust and heat stress, with energy use known before the furnace is built.
- How to tell
- Energy is known. The European reference document gives the theoretical energy to melt soda-lime glass as 2.68 GJ per tonne, and actual use from about 3.5 to over 40 GJ per tonne depending on furnace design, scale and operation; melting is over 75% of the energy in glass manufacture (Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)). A small furnace sits at the high end.
- Respirable crystalline silica from sand and batch handling is kept below the workplace limit: 0.1 mg/m3 over eight hours in Great Britain (Silicosis and respirable crystalline silica (HSE)); NIOSH names glass among exposed industries (Silica (NIOSH topic page)).
- Heat stress at the furnace is assessed with the wet bulb globe temperature method of ISO 7243 (ISO 7243:2017, Ergonomics of the thermal environment: Assessment of heat stress using the WBGT (wet bulb globe temperature) index).
- No lead glass is made for food or drink use. The reference document lists crystal glass with 19% lead oxide among common formulations (Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)); WHO states no level of lead exposure is known to be without harm (Lead poisoning (WHO fact sheet)).
- Options
- Remelting cullet. Using recovered glass is named as an energy-saving technique (Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)). Collection and sorting are covered by the waste pass element "Metals and glass".
- Pot furnaces and day tanks. The reference document describes these as the discontinuous melters used where small amounts are needed or the formulation changes; day tanks reach the region of 10 tonnes a day and are refilled daily (Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)).
- Small electric furnaces. Named in the reference document for special glass (Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)).
- Annealing. Articles pass through an annealing lehr to remove internal stresses (Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)). No small-scale annealing source was opened.
- Settled, open, contested
Settled: silica dust causes silicosis and has published limits (Silicosis and respirable crystalline silica (HSE), Silica (NIOSH topic page)). Settled: glass melting is energy-intensive and small furnaces use far more energy per tonne (Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)). Open: the reference document opened is dated 2001 and archived as superseded; the current version was not read. Contested: the HSE and NIOSH silica figures differ, as the ceramics element notes.
The four stages
- Learn: Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001).
- Design: size the energy supply from the per-tonne figures (Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)); plan dust and heat controls (Silicosis and respirable crystalline silica (HSE), ISO 7243:2017, Ergonomics of the thermal environment: Assessment of heat stress using the WBGT (wet bulb globe temperature) index).
- Build: no construction source was opened; furnace building is work for a qualified person.
- Deploy: dust records and health surveillance (Silicosis and respirable crystalline silica (HSE)); heat assessment (ISO 7243:2017, Ergonomics of the thermal environment: Assessment of heat stress using the WBGT (wet bulb globe temperature) index); know the glass the community discards (Glass: Material-Specific Data).
Resources at each stage
1 Learn
Understand
- Glass: Material-Specific Data Dataset, S0
- Silicosis and respirable crystalline silica (HSE) Guide, S3
- Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001) Reference design, S3
- Silica (NIOSH topic page) Guide, S3
- Lead poisoning (WHO fact sheet) Reference design, S3
2 Design
Size and choose
4 Deploy
Install, run and measure
What changes between 30 adults and 300 people
At 30 adults, glass making is unlikely to pay its energy cost; recovered glass is reused whole or crushed. At 300 people, a studio furnace remelting cullet for small articles is possible where energy is plentiful, with a trained furnace keeper. No source read gives output or costs at either scale.
Reference designs
-
Reference design
Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001)
The first European reference document on glass making, dated December 2001 and now archived as superseded. It covers installations above 20 tonnes a day, describes pot furnaces and day tanks (the latter in the region of 10 tonnes a day) for small batches, gives the theoretical energy to melt soda-lime glass as 2.68 GJ per tonne against actual use of about 3.5 to over 40 GJ per tonne depending on furnace and scale, and states that melting accounts for over 75% of the energy in glass manufacture.
External resource. Not made or verified by Public ProtocolMaturity: EstablishedSafety S3Listed 16 November 2026 -
Reference design
Lead poisoning (WHO fact sheet)
WHO's fact sheet on lead (dated 10 June 2026): no level of exposure is known to be without harm, more than 3.5 million deaths in 2023 are attributed to lead, ceramic glazes are among the products named as containing lead, and the harm is entirely preventable.
External resource. Not made or verified by Public ProtocolMaturity: EstablishedSafety S3Listed 16 November 2026
Parts list
Every resource that supports this element. Those marked External carry the label “External resource. Not made or verified by Public Protocol”.
| Resource | Type | Origin | Maturity | Safety | Licence, as stated at its source |
|---|---|---|---|---|---|
| Glass: Material-Specific Data | Dataset | External | Established | S0 | Not stated on the page opened |
| Silicosis and respirable crystalline silica (HSE) | Guide | External | Established | S3 | Not stated on the page opened |
| ISO 7243:2017, Ergonomics of the thermal environment: Assessment of heat stress using the WBGT (wet bulb globe temperature) index | Standard | External | Established | S2 | © ISO 2017. All rights reserved. |
| Reference Document on Best Available Techniques in the Glass Manufacturing Industry (December 2001) | Reference design | External | Established | S3 | Not stated on the page opened |
| Silica (NIOSH topic page) | Guide | External | Established | S3 | Not stated on the page opened |
| Lead poisoning (WHO fact sheet) | Reference design | External | Established | S3 | Not stated on the page opened |
Depends on, and completes
It is one of 34 elements that complete Manufacturing and repair.
The standing questions
Who supplies and pays for the energy. Who is trained to run the furnace. Who decides whether glass is made or bought.
Environments
No source found for any setting. Ceramics and kilns, with the overlapping silica and kiln hazards, are covered by the gap-sweep element "Ceramics, glazes and kilns".
Safety
State and evidence
Drafted
An editor has written the element's text from the resources listed under it, citing them. It is checked when it is reviewed.
Evidence from a real place or system is recorded here, with what did not work. What the states mean
History
- Drafted in the release of 16 November 2026.