Public Protocol
Platform

Element 9.15

Machine safety by design

Sheet
9.15
Chapter
9 Manufacturing and repair
State
Drafted
Release
16 November 2026
Editor
Contributed by Praecise as open research
Reviewers
To be named at review
Safety
S3, as the chapter
Licence
CC BY-SA 4.0
Resources
7

The element

Requirement

Every machine the community designs, builds, modifies or uses has had its hazards identified, removed where possible and reduced where not, with guards, emergency stops, safe controls and a way to isolate power, and with the remaining risk told plainly to the people who run it.

How to tell
Options
Settled, open, contested

Settled: hazards are identified and eliminated where possible, and the remaining risk reduced (EN ISO 12100:2010 Safety of machinery: General principles for design, risk assessment and risk reduction); guards come before jigs, and information and training deal only with what remains (Introduction to machinery safety). Open: the revision of ISO 12100 adds hygiene and cybersecurity subclauses; a draft is dated January 2025 and the final text is not yet published (prEN ISO 12100 revision project (DIN)). Contested: whether a self-built machine used only by its builder needs the same paperwork as one sold. The self-build guide treats the duties as the same (Sécurité et réglementation (L'Atelier Paysan)); practice varies by country.

The four stages

Resources at each stage

What changes between 30 adults and 300 people

At 30 adults, few machines, one competent person and a shared checklist work. At 300 people there are more machines and more occasional users, so interlocks, lock-off points and a sign-off for each user become necessary, and a person independent of the builder reviews each new design.

Reference designs

  • Reference design

    Modulathe

    Modular open source desktop lathe for metal, wood and plastic. The repository states a 125 mm chuck and an MT5 spindle with a 38 mm through-hole; version 1 is mostly printed, version 2 mostly concrete cast in printed moulds. It warns that lathes are dangerous.

    External resource. Not made or verified by Public ProtocolMaturity: PrototypeSafety S3Listed 16 November 2026

Parts list

Every resource that supports this element. Those marked External carry the label “External resource. Not made or verified by Public Protocol”.

ResourceTypeOriginMaturitySafetyLicence, as stated at its source
Regulation (EU) 2023/1230 on machineryStandardExternalEstablishedS3Not stated on the page opened
Introduction to machinery safetyGuideExternalEstablishedS3Not stated on the page opened
Provision and Use of Work Equipment Regulations 1998 (PUWER)StandardExternalEstablishedS2Not stated on the page opened
prEN ISO 12100 revision project (DIN)StandardExternalPrototypeS3Not stated on the page opened
EN ISO 12100:2010 Safety of machinery: General principles for design, risk assessment and risk reductionStandardExternalEstablishedS3Not stated on the page opened
Sécurité et réglementation (L'Atelier Paysan)GuideExternalEstablishedS3"CC-BY-NC-SA L'Atelier Paysan", in the site footer
ModulatheReference designExternalPrototypeS3"MIT license", as the repository states

Depends on, and completes

Depends on 9.2.

It is one of 34 elements that complete Manufacturing and repair.

The standing questions

Who may remove a guard and refit it. Who decides that a near miss stops a machine. Who pays for the safer design when the cheaper one would do the job.

Environments

Environment profiles for these settings: Small islands and coasts; Arctic, subarctic and permafrost, including sea ice; Extreme cold; Hot deserts; Extreme heat; Tropical rainforest and humid tropics; High humidity; Temperate and boreal forests; Mountains and high altitude; River deltas and flood plains. All environments

Safety

State and evidence

Drafted

An editor has written the element's text from the resources listed under it, citing them. It is checked when it is reviewed.

Evidence from a real place or system is recorded here, with what did not work. What the states mean

History