Element 9.17
Mechanisms, motion and drives
- Sheet
- 9.17
- Chapter
- 9 Manufacturing and repair
- State
- Drafted
- Release
- 16 November 2026
- Editor
- Contributed by Praecise as open research
- Reviewers
- To be named at review
- Safety
- S3, as the chapter
- Licence
- CC BY-SA 4.0
- Resources
- 11
The element
- Requirement
The people who design machines understand how mechanisms move and carry load, can size a frame against the forces on it, and can choose and wire a motor, a driver and a controller that the community can repair and reprogram.
- How to tell
- The designer can state the degrees of freedom of the mechanism and which linkage, cam or gear train produces each motion; these are the subjects of the Carnegie Mellon course notes (Introduction to Mechanisms).
- The forces on the frame have been worked out with free-body diagrams and equilibrium, as an open statics text teaches (Engineering Statics: Open and Interactive).
- The controller runs on open firmware whose source the community holds (LinuxCNC, grblHAL, Klipper).
- Electrical work on drives is done to the national electrical rule by a competent person; open electrical theory is in (Lessons In Electric Circuits).
- Options
- Hand or animal power: no drive electronics, any scale; the EU product rules define a machine by a drive other than human or animal force (Sécurité et réglementation (L'Atelier Paysan)).
- Hydraulic drive: high force from a tractor or separate power unit. The open CEB press runs at a stated system pressure of 2400 psi from a separate hydraulic source (CEB Press (Open Source Ecology)). Hydraulic pressure is a serious injury hazard.
- Stepper or servo motors under open control. LinuxCNC drives mills, lathes, cutters and robot arms (LinuxCNC). grblHAL drives CNC mills on 32-bit microcontrollers, with drivers for more than 15 processor families (grblHAL). Klipper splits work between a general-purpose computer and microcontrollers and lists input shaping and several kinematics (Klipper).
- Brushless motor control: the VESC project publishes open motor controllers used in e-bikes, robots and industry (VESC Project).
- Serial bus servos: the SO-101 arm uses six STS3215 servos per arm, with gear ratios set per joint in the leader arm (Standard Open SO-100 and SO-101 Arms).
- Settled, open, contested
Settled: kinematics and statics are mature, freely taught subjects (Introduction to Mechanisms, Engineering Statics: Open and Interactive). Open: the platform holds no open, opened source for sizing shafts, bearings and fasteners against fatigue; this is a gap. Contested: hobby-grade parts in working machines. Hobby servos and printed frames are cheap and repairable; industrial parts are rated and documented. Choose by the load and the consequence of failure.
The four stages
- Learn: Introduction to Mechanisms, Engineering Statics: Open and Interactive, Lessons In Electric Circuits.
- Design: size frame and joints by statics; for structures that carry people or buildings, use the Eurocodes or the national code (About the EN Eurocodes).
- Build: control from LinuxCNC, grblHAL or Klipper; drives from VESC Project.
- Deploy: keep firmware configuration with the design files (element 9.6).
Resources at each stage
1 Learn
Understand
- Introduction to Mechanisms Course, S0
- About the EN Eurocodes Standard, S3
- Engineering Statics: Open and Interactive Course, S0
- Sécurité et réglementation (L'Atelier Paysan) Guide, S3
- Lessons In Electric Circuits Guide, S0
- Standard Open SO-100 and SO-101 Arms Reference design, S2
2 Design
Size and choose
- Introduction to Mechanisms Course, S0
- About the EN Eurocodes Standard, S3
- Engineering Statics: Open and Interactive Course, S0
- Sécurité et réglementation (L'Atelier Paysan) Guide, S3
- CEB Press (Open Source Ecology) Reference design, S3
3 Build
Build or obtain
- grblHAL Repository, S2
- Klipper Tool, S2
- LinuxCNC Tool, S2
- CEB Press (Open Source Ecology) Reference design, S3
- Standard Open SO-100 and SO-101 Arms Reference design, S2
- VESC Project Repository, S2
4 Deploy
Install, run and measure
- Klipper Tool, S2
- LinuxCNC Tool, S2
- Standard Open SO-100 and SO-101 Arms Reference design, S2
What changes between 30 adults and 300 people
At 30 adults, one control platform for all machines keeps spares and knowledge in one place. At 300 people several platforms may be justified by the machines in use, and a person who understands drives and electrical safety is needed on site.
Reference designs
-
Reference design
CEB Press (Open Source Ecology)
Open hydraulic press for compressed earth bricks. Its wiki page states product release status, version 17.08 as the current model, six full-sized bricks per minute at 12.5 gallons per minute of hydraulic flow, and no power unit supplied; it runs from a separate hydraulic power source.
External resource. Not made or verified by Public ProtocolMaturity: WorkingSafety S3Open, with paid products or servicesListed 16 November 2026 -
Reference design
Standard Open SO-100 and SO-101 Arms
Open, largely 3D-printed robot arms designed by RobotStudio with Hugging Face for the LeRobot learning library. Each arm uses six STS3215 serial bus servos; a leader arm moved by hand teaches a follower arm. The repository gives STEP and STL files, a bill of materials and print gauges.
External resource. Not made or verified by Public ProtocolMaturity: WorkingSafety S2Open, with paid products or servicesListed 16 November 2026
Parts list
Every resource that supports this element. Those marked External carry the label “External resource. Not made or verified by Public Protocol”.
| Resource | Type | Origin | Maturity | Safety | Licence, as stated at its source |
|---|---|---|---|---|---|
| Introduction to Mechanisms | Course | External | Established | S0 | Not stated on the page opened |
| About the EN Eurocodes | Standard | External | Established | S3 | Not stated on the page opened |
| Engineering Statics: Open and Interactive | Course | External | Established | S0 | Not stated on the page opened |
| grblHAL | Repository | External | Established | S2 | Not stated on the page opened (a COPYING file is present) |
| Klipper | Tool | External | Established | S2 | "Klipper software is Free Software"; the licence is named in the repository's COPYING file, not on the page opened |
| Sécurité et réglementation (L'Atelier Paysan) | Guide | External | Established | S3 | "CC-BY-NC-SA L'Atelier Paysan", in the site footer |
| Lessons In Electric Circuits | Guide | External | Established | S0 | Creative Commons License (variant not named on the page) |
| LinuxCNC | Tool | External | Established | S2 | GNU GPLv2 |
| CEB Press (Open Source Ecology) | Reference design | External | Working | S3 | "Open source hardware, controller, and software" under CC-BY-SA 4.0 and GPLv3, as the page states |
| Standard Open SO-100 and SO-101 Arms | Reference design | External | Working | S2 | "Apache-2.0 license", as the repository states |
| VESC Project | Repository | External | Established | S2 | Not stated on the page opened |
Depends on, and completes
It is one of 34 elements that complete Manufacturing and repair.
The standing questions
Who maintains the firmware when its keeper leaves. Who is allowed to work on drive electrics. Who decides when a hobby part is good enough.
Environments
no source found.
no source found.
no source found.
no source found.
no source found.
no source found.
no source found.
Other harsh settings
no source found.
Safety level S3. Moving parts, stored hydraulic pressure and mains electricity can kill. This text names sources; it gives no procedure.
Environment profiles for these settings: Small islands and coasts; Arctic, subarctic and permafrost, including sea ice; Extreme cold; Hot deserts; Extreme heat; Tropical rainforest and humid tropics; High humidity; Temperate and boreal forests; Mountains and high altitude; River deltas and flood plains. All environments
Safety
State and evidence
Drafted
An editor has written the element's text from the resources listed under it, citing them. It is checked when it is reviewed.
Evidence from a real place or system is recorded here, with what did not work. What the states mean
History
- Drafted in the release of 16 November 2026.