Public Protocol
Platform

Element 10.10

Low-power and battery-powered devices

Sheet
10.10
Chapter
10 Electronics and circuit design
State
Drafted
Release
16 November 2026
Editor
Contributed by Praecise as open research
Reviewers
To be named at review
Safety
S2, as the chapter
Licence
CC BY-SA 4.0
Resources
9

The element

Requirement

A device meant to run unattended has a written energy budget: the current in each state, the time spent in each, and the battery or solar supply that covers it with margin, using a certified cell and charger.

How to tell
  • Every state the device passes through has a current from the datasheet and a measured value. The ESP32-C6 datasheet gives peak Wi-Fi transmit currents of 252 to 354 mA at 3.3 V, against 7 microamps in deep sleep and 1 microamp powered off (ESP32-C6 Series Datasheet, version 1.6). The nRF54L15 page gives 0.7 to 2.9 microamps asleep, 3.4 mA receiving and 4.8 mA transmitting at 0 dBm, all at 3 V (nRF54L15).
  • The average current is calculated as the time-weighted sum of these states, and the battery life follows from it. The ratio above, tens of thousands to one between transmitting and sleeping on the same chip, is why the time awake decides the life.
  • The budget is checked by measurement on the bench (sigrok).
  • For cellular devices, the model is checked against the network settings. One measured study finds NB-IoT and LTE-M lifetime depends on traffic, coverage and network configuration, and can reach the 10 years 3GPP requires (Modelling and Experimental Validation for Battery Lifetime Estimation in NB-IoT and LTE-M).
Options
Settled, open, contested

Settled: the gap between awake and asleep is several orders of magnitude on current chips (ESP32-C6 Series Datasheet, version 1.6, nRF54L15). Open: real lifetime in the field. The datasheets give typical values at 25 degrees Celsius; the cellular study shows coverage and network settings move the result (Modelling and Experimental Validation for Battery Lifetime Estimation in NB-IoT and LTE-M). Contested: primary cells or rechargeable with solar. Primary cells are simple and have no charger to fail. Solar removes battery replacement and adds a charger, a panel and a cell that ages. No open source comparing the two for small nodes was opened in this work.

The four stages

Resources at each stage

What changes between 30 adults and 300 people

At 30 adults, a handful of sensors on bought boards with certified packs, and one person who measures each design once. At 300 people, tens to hundreds of nodes: a standard battery and charger for all designs, a replacement schedule, and a store of cells kept to the safety data sheet.

Reference designs

  • Reference design

    ESP32-C6 Series Datasheet, version 1.6

    The maker's datasheet for the ESP32-C6. It gives a recommended ambient range of -40 to 105 degrees Celsius for every variant, peak Wi-Fi transmit currents of 252 to 354 mA at 3.3 V, and states a deep-sleep consumption of 7 microamps and 1 microamp with the chip powered off.

    External resource. Not made or verified by Public ProtocolMaturity: EstablishedSafety S0CommercialListed 16 November 2026
  • Reference design

    Libre Solar

    Open designs for charge controllers and battery management systems, with a learning resource on how such systems work.

    External resource. Not made or verified by Public ProtocolMaturity: Not assessedSafety S2Listed 16 November 2026

Parts list

Every resource that supports this element. Those marked External carry the label “External resource. Not made or verified by Public Protocol”.

ResourceTypeOriginMaturitySafetyLicence, as stated at its source
ESP-IDF Security Overview (ESP32-C6, v6.1.1)GuideExternalEstablishedS1Not stated on the page opened
ESP32-C6 Series Datasheet, version 1.6Reference designExternalEstablishedS0Not stated on the page opened
Regulation (EU) 2023/1542 on batteries and waste batteriesStandardExternalEstablishedS2Not stated on the page opened
IEC 62368-1:2023 Audio/video, information and communication technology equipment - Part 1: Safety requirementsStandardExternalEstablishedS2Not stated on the page opened
Libre SolarReference designExternalNot assessedS2BMS firmware: Apache-2.0, as stated in its repository
Modelling and Experimental Validation for Battery Lifetime Estimation in NB-IoT and LTE-MPaperExternalReplicatedS0arXiv non-exclusive distribution licence 1.0
nRF54L15ToolExternalWorkingS0Not stated on the page opened
nRF9151ToolExternalWorkingS0Not stated on the page opened
sigrokToolExternalEstablishedS0GNU GPL, version 3 or later

Depends on, and completes

Depends on 10.2, 10.6.

It is one of 11 elements that complete Electronics and circuit design.

The standing questions

Who replaces batteries and when. Who stores and disposes of them. Who decides how often a device reports.

Safety level S2: lithium cells can catch fire. This text states the requirement and names the rules; it is not a procedure. Use certified cells and chargers, follow IEC 62368-1 (IEC 62368-1:2023 Audio/video, information and communication technology equipment - Part 1: Safety requirements) and the battery rules of the place (Regulation (EU) 2023/1542 on batteries and waste batteries), and have designs checked by a person qualified in electrical safety.

Environments

Environment profiles for these settings: Arctic, subarctic and permafrost, including sea ice; Extreme cold; Mountains and high altitude; Hot deserts; Extreme heat; Small islands and coasts; Remote and off-grid sites; Tropical rainforest and humid tropics; Temperate and boreal forests; River deltas and flood plains; High humidity. All environments

Safety

State and evidence

Drafted

An editor has written the element's text from the resources listed under it, citing them. It is checked when it is reviewed.

Evidence from a real place or system is recorded here, with what did not work. What the states mean

History